Cap Torque Tester

Cap Torque Testers

Cap Torque Testers available in many torque ranges

5 Used cap torque testers in stock, 4 digital and one spring, conditions vary. Listed under used equipment other.

Spring torque tester requires no power to operate.

Spring Cap Torque Tester, manual read out.

0-25 inch pounds or 0-50 inch pounds, Price: $1650

0-100 inch pounds, price $1650

Spring Cap Torque Tester

Digital readout operates from 120 VAC or 9 VDC, alkaline batteries.

Digital CAP Torque Tester

Digital read out, price $2209

Digital cap torque tester A, read out available to 100th of an inch pound.

Nice unit, accurate easy to use, available with all the bells and whistles.

Contact NPS for pricing

Spring Cap Torque Tester

The Spring Torque Tester is designed to control cap tightness – an essential factor – in bottling operations:

	When caps are not applied tightly enough, leakage or evaporation of product may occur.
	When caps are applied too tightly, molded closures may be susceptible to breakage, or the caps may be difficult to remove.

Spring Torque Testers are available in two different models:

	The MR model has an indicator on the removal side only.
	The MRA model has indicators on both the removal and application sides.

Both the MR and MRA models are available in the following standard ranges:

	0-25 inch lbs., which reads in 1 inch lb. increments
	0-50 inch lbs., which reads in 2 inch lb. increments
	0-100 inch lbs., which reads in 5 inch lb. increments
	0-150 inch lbs., which reads in 10 inch lb. increments

Special order ranges are available:

	0-2 inch lbs., which reads in 0.1 inch lb. increments
	0-5 inch lbs., which reads in 0.2 inch lb. increments
	0-10 inch lbs., which reads in 0.5 inch lb. increments

The Spring Torque Testers have an accuracy of ±4% of full scale or reading.

Spring Torque Testers are shipped approximately one to two weeks after receipt of firm order. We ship standard UPS unless otherwise specified by customer. The Spring Torque Tester is shipped double-wrapped and double-boxed for maximum protection.

	Net weight of tester: 12 lbs.
	Shipping information: 15 lbs., 19 ½" x 11 ½" x 5 ¾"

For an up charge, we can furnish these testers with a Teflon finish on all exposed metal parts. This provides a hard, wear-resistant, anti-stick, permanently lubricated surface that will resist chipping, cracking, flaking, and peeling. This Teflon coating will protect the tester from damage by most chemicals, ingredients, and solvents.

We sell calibration kits , or we calibrate or repair testers when they are shipped to us.

Digital Cap Torque Tester

The Digital Torque Tester makes control of closure tightness easier and more reliable than ever before. The Digital Torque Tester is one step above the Spring Torque Tester, which has been setting the industry standard for years.

The Digital Cap Torque Tester:

	covers the entire testing range of cap sizes operating from 0-100 inch lbs. for both removal and application.
	reads in 0.1 inch lb. increments.
	has an accuracy of ±2% of full scale or reading.
	holds the peak reading for approximately 30 seconds, so that readings can be recorded manually.
	operates on either 110 V using a step-down transformer with 9 V output or a 9 V alkaline battery for use in remote or laboratory locations.

We ship standard UPS unless otherwise specified by customer. The Digital Cap Torque Tester is shipped double-wrapped and double-boxed for maximum protection.

	Net weight of tester: 12 lbs.
	Shipping information: 15 lbs., 19 ½" x 11 ½" x 5 ¾"

We sell calibration kits , or we calibrate or repair cap testers when they are shipped to us.

The digital cap tester has the option of being linked to your RS232 computer or printer by a serial cable. This is an upgrade, additional charges will apply.

Cap Torque Tester A

This cap torque tester offers programmable high/low set points for go/no-go testing. ORANGE lights up for measurements less than Low set point, GREEN for between High and Low set point, and RED for over High set point.

Store up to 960 values in memory, which can be transmitted using the serial output. Use the real time mode to display torque transients, or peak mode to capture the peak torque achieved during a test. Selectable measuring units of lbf-in, kgf-cm, or N-cm.

Cap testers include AC adapter/charger and built-in NiCad rechargeable batteries, 1" high standard pegs (optional long pegs available). A calibration kit is also available.

Key Features

	Programmable high/low set points with color-coded LED indicators and output signal for quick go/no go testing
	960 Data memory for computer download
	Clamps containers from 1/2"~ 7" in diameter
	lbf-in, kgf-cm, and N-cm units are selectable
	RS-232C, Digimatic and Analog outputs
	Both clockwise and counterclockwise operation
	Overload capacity 200% of F.S.
	Real time and peak mode (selectable)
	Tare function
	Overload alarm and output signal
	Can be operated with internal rechargeable battery or AC adapter

Turn knob to clamp container, then twist cap by hand to measure torque

Specifications

Accuracy:	± 0.5% Full scale ± 1 digit
Measuring frequency:	30 times/s
Selectable units:	Nm, kgfm, Lb.in
Overload capacity:	150% Full scale (flashing LED beyond 108% Full scale), open collector output signal
Zero adjustment:	10% Full scale
A/D Converter:	16 bit
Memory:	non-volatile, recall up to 960 loads, recall both peaks, open and close torque
Setpoints:	Min, Max (programmable), with output signal
Output signal:	RS232C (8,1,N,19200), analog ± 2V DC, Open collector 4x (+NG, Ok, -NG, OVL), max. 30V DC, 10mA, Mitutoyo Digimatic
Temperature range:	5 - 45°C
Air humidity:	85% RH, max.
Power supply:	100V ... 240V AC, 50Hz
Housing dimensions:	(approx.) 324x210x130 mm (LxWxH)
Weight, net (gross):	ca. 4900 g (ca. 5900g)

Calibration kit including weights for cap torque tester A

Cap torque tester A, with printer, button, and cords

Printer

Cap Torque Tester A

Transfer information button

Visa and Master Card accepted.

Home

NEUMANN PACKAGING SERVICES
1765 Pine Grove Drive, Asheboro, North Carolina 27205
Phone: 336-683-9834 / Fax: 336-683-9833 / E-mail: neumannpack@triad.rr.com